Saint-Ambroise-de-Kildare, LanaudièreMon–Fri · 8 am–5 pm450 759-0472
Martin Remorques et V.R. Find my trailer
MARTIN REMORQUES / SALES • PARTS • SERVICE

Trailer wiring and lighting

A light that won’t come on, a plug that lost contact, lights flickering on their own: at our Saint-Ambroise-de-Kildare workshop, we find the cause and fix it. And we handle wiring for all types of vehicles.

The workshop’s repair and maintenance door, at 270, route 343
WHAT’S INCLUDED

From the vehicle plug to the last light

On a trailer, the electrical problem is rarely the bulb. It’s the ground, a rusty connection or a pinched wire.

Top-view drawing of a trailer and its wiring, with a close-up of the 7-way plug: the junction box, ground, the harness along the frame, marker lights, tail lights, plate light and brake wires
The trailer from above, with its wiring
  1. Troubleshooting: running, brake, turn and plate lights

  2. Grounds and rusty connections

  3. The trailer plug and the vehicle plug

  4. Replacing damaged wiring, well protected and securely fastened

  5. LED lights: running, reverse or work lights

  6. Vehicle wiring for towing, on all types of vehicles

  7. The link to the electric brakes and controller

  8. Parts from our parts department

THE SIGNS

The failures we see most

A tired ground gives odd symptoms. If this sounds familiar, that’s good news: it can be found.

Recognize one of these signs?

Call the shop or ask for an appointment. We’ll look at the trailer and tell you what it needs.

  • By eye

    A dim light, or one that lights when another blinks

  • On the road

    Lights that flicker on their own or die over bumps

  • On the road

    Brakes that stop responding along with the lights

  • By eye

    A plug gone green with salt, or bent

  • By eye

    A vehicle fuse that blows when you plug in the trailer

  • By eye

    No trailer lights after changing vehicles

HOW IT WORKS

Search, find, fix

  1. You describe the problem

    Which lights, when, and whether it’s tied to one vehicle. Bring the vehicle if you can.

  2. We test

    We check the vehicle, plug, ground and each circuit.

  3. We repair it properly

    Connections redone, wire protected and fastened, so it lasts.

  4. We check it with you

    Every light tested, and you leave knowing what was done.

Why trailers have so many light problems

A trailer lives outdoors. Its wiring runs under the frame through salt and water and gets shaken at every bump. Most lights return to ground through the frame: when a connection rusts, the current looks for another path and the lights start doing strange things. That kind of failure isn’t fixed by changing a bulb.

One customer had LED reverse lights installed on a dump trailer, then saw flickering from a ground issue. It was corrected at the garage. That’s exactly the kind of detail we take seriously.

The Martin Remorques store and workshop, at 270, route 343
The store and workshop, at 270, route 343.

Switching to LED lights

LED lights draw less, last longer and handle vibration better. They’re also more sensitive to a bad connection. A replacement is a good time to redo the grounds and protect the wiring. On a work trailer, work lights or reverse lights make all the difference when backing up on a job site at night.

Vehicle wiring

We install wiring for all types of vehicles: it’s what connects your car, SUV or truck to the trailer. If your vehicle has never towed, or doesn’t have the right plug, see what we do for trailer hitches.

4-way or 7-way: understanding your plug

A flat 4-way plug handles the lights: running, brake and turn signals, plus the ground. It’s what you’ll find on most small utility trailers. A round 7-way plug adds the electric brake signal, a power feed to charge a battery and often the reverse lights. It’s the plug on dump trailers, enclosed trailers and big flatbeds.

Adapters exist, but they don’t work miracles: an adapter won’t give a brake signal to a vehicle that isn’t wired for it. If you change trailers or vehicles, make sure the two speak the same language. Keep your plugs clean as well: a little dielectric grease on the contacts and a cap on the vehicle plug prevent plenty of salt-related failures. When a plug goes green, clean or replace it before the problem reaches the lights. Before a long trip, test everything with the trailer hooked up, because a connection that works in the driveway can still fail once the road starts shaking it. If you tow in the dark or in winter, working lights aren’t just a legal detail: they’re how the driver behind you knows what you’re about to do.

If you don’t know which plug you have, take a photo of both, on the vehicle and on the trailer: it helps us answer you right away.

WORKSHOP APPOINTMENT

Book a workshop appointment

Tell us which trailer and what work: we call you back to set the date and plan the parts.

Rather talk to someone? 450 759-0472
Monday to Friday, 8 a.m. to 5 p.m.

Work needed

We call you back to confirm the date.

FREQUENTLY ASKED QUESTIONS

Your questions,
our answers

Ask a question
My lights flicker on their own. Where does that come from?

Most often from a bad ground or a rusty connection. The circuit has to be tested to confirm it.

Do you wire vehicles too?

Yes, we install wiring for all types of vehicles. Tell us the make, model and year.

Can you install LED or reverse lights?

Yes. A customer had LED reverse lights fitted to a dump trailer, with the wiring protected and securely fastened. Tell us what you want and on which trailer.

Should I bring my vehicle?

If the problem only happens with one vehicle, yes. It lets us check both sides of the plug.

My lights work with one vehicle but not the other. Why?

The problem is then often on the vehicle side: the plug, a fuse or the wiring. Bring both vehicles if you can, so we can compare them and find the difference.

Which plug do I need?

A 4-way plug is enough for a trailer without electric brakes. With electric brakes, you need a round 7-way plug and a controller.

Let’s talk it through

Your next project
Let’s talk

A trailer in mind, a part to find or maintenance to discuss? Get in touch with our team.

Talk to the team450 759-0472Mon–Fri · 8 am–5 pm