Electric and hydraulic trailer brakes
Trailer brakes stop the trailer’s weight together with the vehicle. Electric on most trailers, hydraulic on boat trailers, drum or disc, they wear out and are replaced as complete assemblies, side by side.

Choose your part
Electric brakes
In an electric drum brake, a magnet powered by the vehicle’s controller rubs against the face of the drum; as it turns, it pushes a lever that spreads the shoes against the drum. The more current the controller sends, the harder the trailer brakes. The magnet and the shoes wear together.
The size follows the axle: often 10 × 2 1/4 in. for a 3,500 lb axle, 12 × 2 in. for 5,200 and 6,000 lb, and 12 1/4 in. in diameter for 7,000 lb, in a width that depends on the model. Dexter makes complete, ready-to-bolt assemblies, left and right, with magnets, shoes and springs.
Timbren94545PR pair of 10 in. electric brake hubs, 3,500 lb, 5 on 4.5 in.Hydraulic brakes
On a boat trailer, the hydraulic surge coupler pushes brake fluid to the wheels when the trailer pushes against the vehicle while braking. Disc brakes, in stainless steel or with an anti-corrosion coating, stand up to salt and fresh water better than drums, which trap water.
Heavy trailers can also take electric-over-hydraulic brakes: an electric pump, controlled by the vehicle’s controller, powers strong disc brakes.
Timbren94655PR pair of 10 in. electric brake hubs, 3,500 lb, 6 on 5.5 in.Brakes and hubs together
When the drum is worn or scored, it is replaced with the hub, which is a single part on most trailers: the brake and hub kit comes with bearings, seals and studs. Our suppliers stock these kits for the common axles, along with replacement parts for drum and disc brakes.
Timbren500886PR pair of 12 in. electric brake hubs, 7,000 lb, 8 on 6.5 in.In practice
An equipment trailer that brakes poorly and pulls to one side gets new electric brake assemblies on both sides of each axle, and the controller is set up again. A boat trailer owner switches from drums to disc brakes so the brakes no longer need redoing every season.
TimbrenASR2000S01 Timbren axle-less trailer suspension, 2,000 lbGood to know
New brakes need bedding in: a few gentle stops at moderate speed, with the trailer loaded, seat the shoes against the drums. The controller setting is then redone, because new brakes bite harder than worn ones, and the old gain setting may now lock the wheels.
TimbrenASR3500S05 Timbren axle-less trailer suspension, 3,500 lb, brake flangeWhat we can order
- Complete electric brake assemblies, left and right
- Magnets, shoes and springs
- Hydraulic drum and disc brakes
- Brake and hub kits
- Electric-over-hydraulic brakes
- Lines, wheel cylinders and calipers
Care
Have the brakes inspected once a year: shoe or pad thickness, magnet wear, drum or disc condition, wiring. Manually adjusted electric brakes are adjusted regularly to keep them effective.
Always replace brakes in pairs, on both sides of the same axle, so the trailer brakes straight.
TimbrenASR5200S01 Timbren axle-less trailer suspension, 5,200 lb, brake flangeOrdering at Martin Remorques
Tell us the axle rating and the brake type, or bring the trailer in: we order the assemblies and our shop installs and adjusts them.
Martin Remorques orders its parts from its suppliers, depending on the manufacturer, and receives them at its Saint-Ambroise-de-Kildare counter. Bring the part number, a photo of the part or its label, and the make, model and year of your trailer or vehicle: we check fit, price and lead time before we order.
Our shop in Saint-Ambroise-de-Kildare installs what we sell: hitches, brakes, wiring, axles, bearings, winches and accessories. You leave with a trailer ready to roll, and we keep a note of the part for next time.
You can also come to the counter, at 270, route 343, Monday to Friday from 8 am to 5 pm, with the part to replace: it is often the fastest way to find the right one.

Manufacturers of this part type
The availability of a part and of each model is confirmed with the team before ordering.
Request a part
Describe the part or give its number: we find the right one, confirm price and lead time, and can install it.
Rather talk to someone? 450 759-0472
Monday to Friday, 8 a.m. to 5 p.m.
When should the brakes be replaced?
When the shoes or magnets are worn, or the trailer brakes poorly or pulls to one side.
Discs or drums for a boat?
Discs resist water better; they are recommended for trailers that go in the water often.
Can brakes be added to a trailer without them?
Often, yes, if the axle has brake flanges; otherwise the hubs or the axle are changed.
Are magnets sold on their own?
Yes, but they are usually replaced together with the shoes, since both wear at the same rate and a new magnet on a worn shoe, or the reverse, rarely brakes as well as a matched set.
Do you set the controller after installing brakes?
Yes, with the trailer hitched, before it leaves, so the new brakes and the controller work together from the very first stop on the road.
How do I order a part from Martin Remorques?
Fill in the part request on this page or call us at 450 759-0472 with the part number or a photo. We confirm fit, price and lead time before ordering.
Can Martin Remorques install the part?
Yes. Our shop installs the parts we sell, by appointment, and checks the rest of the trailer when needed: lights, brakes, bearings and hitch.
Your next project
Let’s talk
A trailer in mind, a part to find or maintenance to discuss? Get in touch with our team.



