Trailer hitch balls
The ball takes the trailer’s coupler. A small part with a big job: its diameter has to match the coupler, and its rating the loaded trailer.

Choose your part
Three diameters
The 1 7/8 in. ball serves small light trailers, up to about 2,000 lb. The 2 in. ball is the most common, from 3,500 to 10,000 lb depending on the model. The 2 5/16 in. ball serves heavy trailers and goosenecks, up to 30,000 lb depending on the model.
The diameter is stamped on the coupler and on the ball. A ball too small for its coupler can pop off on a bump: it is one of the causes of trailers coming loose on the road.
Curt40174 2 in. trailer ball, 1 x 3 in. shank, 6,000 lbThe shank and the hole
The ball shank has to match the hole in the ball mount: 3/4, 1 or 1 1/4 in. in diameter. Its length has to leave a few threads past the nut once tightened. A thin shank in a big hole eventually works loose.
Curt makes chrome and stainless steel balls in every rating, Stealth Hitches the 1 7/8, 2 and 2 5/16 in. balls for its hitches, and Buyers Products balls for equipment and work trailers.
Curt40176 2 5/16 in. trailer ball, 1 1/4 x 3 in. shankTightening the ball properly
The ball is tightened to the torque the manufacturer specifies, often several hundred foot-pounds for large shanks: an ordinary wrench is not enough. Our shop installs and torques balls properly, and checks them during service.
Curt40047 RockerBall 2 in. cushion trailer ball, 7,500 lbIn practice
An owner who tows a small watercraft trailer and a 2 in. utility trailer keeps two balls, or a two-ball mount. A landscaping company standardizes all its trailers on 2 5/16 in.: one ball for the whole fleet.
Draw-Tite63864 2 5/16 in. trailer ball, 25,000 lbChoosing the rating
The ball rating has to cover the loaded trailer’s gross weight, not just its empty weight: a 1,500 lb utility trailer carrying 2,000 lb of stone needs a ball rated for at least 3,500 lb.
A raised ball lifts the coupler an inch or two on a low trailer, and a long-shank ball goes through thick mounts. A stainless steel ball does not rust and keeps its finish, a good choice for a boat trailer that goes in the water.
Curt13902 Class 3 multi-fit hitch, 2 in. receiverBall sizes
- 1 7/8 poUp to about 2,000 lb: small light trailers
- 2 po3,500 to 10,000 lb depending on the model: most trailers
- 2 5/16 po6,000 to 30,000 lb depending on the model: heavy trailers and goosenecks
What we can order
- 1 7/8, 2 and 2 5/16 in. balls
- 3/4, 1 and 1 1/4 in. shanks, short or long
- Chrome and stainless steel balls
- Gooseneck balls
- Ball covers
- Replacement nuts and washers
Care
A thin coat of grease on the ball reduces wear and noise; a ball cover keeps it clean between trips.
Replace a worn, flattened or rusted ball: it no longer holds the coupler properly.
Curt15511 Class 5 multi-fit hitch, 2 in. receiverOrdering at Martin Remorques
Tell us your coupler size, the trailer weight and the hole in your ball mount: we find the right ball.
Martin Remorques orders its parts from its suppliers, depending on the manufacturer, and receives them at its Saint-Ambroise-de-Kildare counter. Bring the part number, a photo of the part or its label, and the make, model and year of your trailer or vehicle: we check fit, price and lead time before we order.
Our shop in Saint-Ambroise-de-Kildare installs what we sell: hitches, brakes, wiring, axles, bearings, winches and accessories. You leave with a trailer ready to roll, and we keep a note of the part for next time.
You can also come to the counter, at 270, route 343, Monday to Friday from 8 am to 5 pm, with the part to replace: it is often the fastest way to find the right one.

Manufacturers of this part type
Buyers ProductsBuyers Products
Work truck equipment: toolboxes, warning lights, hitches and snowplow parts.
The availability of a part and of each model is confirmed with the team before ordering.
Request a part
Describe the part or give its number: we find the right one, confirm price and lead time, and can install it.
Rather talk to someone? 450 759-0472
Monday to Friday, 8 a.m. to 5 p.m.
How do I find my trailer’s ball size?
It is stamped on the coupler: 1 7/8, 2 or 2 5/16 in.
Can a 2 in. ball go in a 2 5/16 in. coupler?
No: the ball has to be exactly the coupler’s size.
Should the ball be greased?
Yes, lightly, unless the coupler manufacturer says otherwise.
Chrome or stainless ball?
Both hold up well; stainless resists water and salt better over time, which matters for boat trailers and for vehicles driven all winter on salted roads.
When should a ball be replaced?
When it is worn, flattened, cracked or deeply rusted; a worn ball lets the coupler move and can let it pop off over a bump, so it is cheap insurance to replace it.
How do I order a part from Martin Remorques?
Fill in the part request on this page or call us at 450 759-0472 with the part number or a photo. We confirm fit, price and lead time before ordering.
Can Martin Remorques install the part?
Yes. Our shop installs the parts we sell, by appointment, and checks the rest of the trailer when needed: lights, brakes, bearings and hitch.
Your next project
Let’s talk
A trailer in mind, a part to find or maintenance to discuss? Get in touch with our team.














