Draw-Tite hitches
Draw-Tite is an American brand of receiver hitches made for each vehicle: cars, SUVs, vans and pickups, from Class I to Class V, at the rear and at the front. Martin Remorques orders the Draw-Tite hitch for your vehicle and installs it with its wiring.
Choose your part
A hitch made for your vehicle
Each Draw-Tite hitch is designed for a specific make, model and years: it bolts to the mounting points the manufacturer provides, most of the time without drilling. It comes with its hardware and instructions, and our shop installs it in a few hours.
For a recent vehicle, the right hitch sometimes depends on the trim: engine, bumper, parking sensors or suspension. That is why we check the exact trim before ordering.
Draw-Tite41955 Ultra Frame Class 5 hitch, 2 in. receiverFrom Class I to Class V
Class I and II hitches, with a 1 1/4 in. receiver, suit cars and small SUVs, for a bike rack or a small trailer. Classes III and IV, with a 2 in. receiver, equip SUVs, vans and pickups that pull campers, boats or utility trailers. Class V serves heavy trucks.
The real capacity remains the lowest of the hitch, the ball mount, the ball and the vehicle: the vehicle manual gives its towing capacity and allowed tongue weight.
Draw-Tite25007 Class 1 hitch, 1 1/4 in. receiver, Honda AccordThe matching accessories
A hitch is completed by a ball mount with the right drop, a ball of the right size, a pin and clip, and a harness that powers the trailer lights. On many vehicles, a model-specific harness plugs in without cutting any wire.
A Draw-Tite front hitch, on vehicles that have one, takes a removable winch, a bike rack or a basket, and helps place a trailer in a tight spot.
Draw-Tite76638 Class 3 hitch, 2 in. receiver, Subaru SolterraAt Martin Remorques
We order the Draw-Tite hitch that fits your vehicle and what you want to tow, install it with the wiring and check that the trailer sits level behind the vehicle. We also offer Curt and Stealth Hitches hitches, depending on the vehicle and the use.
Draw-Tite65086 front mount receiver, 2 in., Chevrolet Silverado 1500The right hitch the first time
The surest way to get the right hitch is to start from the vehicle: make, model, year, trim, and sometimes the bumper type or a factory tow package. With that information, the matching Draw-Tite hitch is found in the manufacturer’s catalogue, with its class, its rating and the harness that goes with it.
Then comes the use: a bike rack asks little, a 6,000 lb camper needs a Class III or IV and often weight distribution, and a trailer with electric brakes needs a brake controller.
Curt13902 Class 3 multi-fit hitch, 2 in. receiverA clean installation
During installation, our shop removes factory shields or brackets when needed, bolts the hitch on at the specified torque, routes the harness away from heat and moving parts and checks every trailer light. You leave with a hitch ready to tow, and we keep the reference on file for next time.
Curt15511 Class 5 multi-fit hitch, 2 in. receiverWhat we can order
- Class I to V rear hitches
- Front mount hitches
- Ball mounts and balls
- Hitch wiring harnesses
- Pins and clips
- Installation at our shop
Care
Check the hitch bolts once a year, clean the receiver and touch up paint chips to prevent rust. Remove the ball mount when you are not towing.
Curt12923 Class 2 multi-fit hitch, 1 1/4 in. receiverOrdering at Martin Remorques
Tell us your vehicle’s make, model, year and trim and what you want to tow: we order the right Draw-Tite hitch and install it.
Martin Remorques orders its parts from its suppliers, depending on the manufacturer, and receives them at its Saint-Ambroise-de-Kildare counter. Bring the part number, a photo of the part or its label, and the make, model and year of your trailer or vehicle: we check fit, price and lead time before we order.
Our shop in Saint-Ambroise-de-Kildare installs what we sell: hitches, brakes, wiring, axles, bearings, winches and accessories. You leave with a trailer ready to roll, and we keep a note of the part for next time.
You can also come to the counter, at 270, route 343, Monday to Friday from 8 am to 5 pm, with the part to replace: it is often the fastest way to find the right one.

The manufacturer
The availability of a part and of each model is confirmed with the team before ordering.
Request a part
Describe the part or give its number: we find the right one, confirm price and lead time, and can install it.
Rather talk to someone? 450 759-0472
Monday to Friday, 8 a.m. to 5 p.m.
Is there a Draw-Tite hitch for my vehicle?
Draw-Tite covers most cars, SUVs, vans and pickups; we check your exact trim.
Does installation need drilling?
Rarely: most bolt to the manufacturer’s mounting points.
Which class do I need?
The one that covers your loaded trailer, without going over your vehicle’s capacity.
How do I order a part from Martin Remorques?
Fill in the part request on this page or call us at 450 759-0472 with the part number or a photo. We confirm fit, price and lead time before ordering.
Can Martin Remorques install the part?
Yes. Our shop installs the parts we sell, by appointment, and checks the rest of the trailer when needed: lights, brakes, bearings and hitch.
Your next project
Let’s talk
A trailer in mind, a part to find or maintenance to discuss? Get in touch with our team.












