Saint-Ambroise-de-Kildare, LanaudièreMon–Fri · 8 am–5 pm450 759-0472
Martin Remorques et V.R. Find my trailer
MARTIN REMORQUES / SALES • PARTS • SERVICE

Trailer brake repair

Trailer brakes that pull, lock up or stop responding are not something to live with on Route 343. Our mechanics check, adjust and repair your trailer brakes in Saint-Ambroise-de-Kildare, in Lanaudière.

The workshop’s repair and maintenance door, at 270, route 343
WHAT’S INCLUDED

The whole braking circuit

A brake that works badly is not always a brake problem. We look at the full chain, from the plug to the drum.

Drawing of an electric trailer brake with the drum off: the shoes and their linings, the return springs, the magnet and its lever, the adjuster, the backing plate and the brake wires
Electric drum brake
  1. The linings, drums and return springs

  2. Electric brake magnets and their wear

  3. Brake adjustment, left side and right side

  4. Brake wiring and connections, often attacked by salt

  5. The breakaway system and its battery

  6. On a surge brake trailer: the actuator and master cylinder

  7. Setup with your brake controller, on the road or in the shop

  8. Replacement of worn parts, ordered through our parts department

THE SIGNS

Your brakes are talking to you

Don’t wait for a hill or a job site to deal with it. These signs are worth a visit.

Recognize one of these signs?

Call the shop or ask for an appointment. We’ll look at the trailer and tell you what it needs.

  • On the road

    The trailer pushes the vehicle under braking

  • On the road

    One side locks up or pulls harder than the other

  • By ear

    You hear grinding or rubbing at the wheels

  • By touch

    One wheel is unusually hot after a trip

  • By eye

    The controller shows an error or no longer detects the trailer

  • On the road

    The brakes do nothing, even at maximum

HOW IT WORKS

Find the cause, then fix it

  1. You describe the problem

    When it happens, on which side, with what load. Tell us which controller you have too.

  2. We check the circuit

    Wiring, connections, magnets, linings and drums, wheel by wheel.

  3. We explain

    You know what is worn, what needs replacing and why, before we order.

  4. We repair and adjust

    Once the parts are on, we adjust the brakes so both sides work evenly.

Electric or surge brakes?

Most tandem axle trailers have electric brakes: a magnet in each drum, operated by the controller installed in the vehicle. They need regular adjustment because the linings wear. Surge brakes apply when the trailer pushes against the hitch: the actuator drives a master cylinder, then hydraulic brakes. If you don’t know which one you have, that’s fine: we look at it with you.

The Martin Remorques store and workshop, at 270, route 343
The store and workshop, at 270, route 343.

What the SAAQ requires

In Québec, the SAAQ requires brakes on a trailer whose weight, load included, reaches 1,300 kg or exceeds half the weight of the towing vehicle. A car hauler or a dump trailer gets there fast. The brakes, lights and chains must be connected to the vehicle and in good working order.

For your specific use, the simplest thing is to tell us what you tow and with which vehicle. Your brake controller also has to be set for the day’s load: an empty trailer and a full one do not brake the same way.

Salt, the main culprit

Around here, wear isn’t always what finishes brakes. Salt attacks magnets, connections and drums. A trailer that sits for months with damp brakes can also wake up with stuck linings. Moving the wheels and rinsing the underside in spring helps a lot.

Setting your brake controller properly

The controller sends current to the trailer brakes when you brake. Too low, and the vehicle does all the work while the trailer pushes. Too high, and the trailer wheels lock up. The right setting depends on the day’s load: an empty trailer needs much less power than a full one.

The method is simple. On a dry, quiet road, at low speed, apply the controller by hand. The trailer wheels should almost lock, without pulling to one side. Lower the setting a little, then test again. Do it again whenever the load changes much. If the brakes barely respond, even at maximum, the problem is elsewhere: adjustment, magnets or wiring. That’s when it’s worth coming to see us. Don’t just turn the controller up to compensate: more current won’t make up for a worn magnet or a bad ground, and it can hide a problem that gets worse with every trip. A brake that has been checked and adjusted on both sides also means less wear on your vehicle’s own brakes, especially in hills or with a heavy load behind you.

WORKSHOP APPOINTMENT

Book a workshop appointment

Tell us which trailer and what work: we call you back to set the date and plan the parts.

Rather talk to someone? 450 759-0472
Monday to Friday, 8 a.m. to 5 p.m.

Work needed

We call you back to confirm the date.

FREQUENTLY ASKED QUESTIONS

Your questions,
our answers

Ask a question
Does my trailer need brakes?

In Québec, according to the SAAQ, yes if its weight with the load reaches 1,300 kg or exceeds half the weight of the towing vehicle. If in doubt, tell us what you tow.

My brakes only work on one side. Is that dangerous?

Yes, avoid towing a load. It can come from the wiring, a magnet or the adjustment. Call us at 450 759-0472 to book a time.

Can you install my brake controller?

The controller is part of the vehicle wiring. See what we do for trailer hitches or call us with your vehicle model.

How much does a brake repair cost?

It depends on the trailer, the number of axles and what needs replacing. We talk it over with you before ordering parts.

My trailer brakes keep locking up. Why?

The controller may be set too high for the day’s load, or a brake may be badly adjusted. Lower the setting and test again. If it continues, have the brakes looked at.

Let’s talk it through

Your next project
Let’s talk

A trailer in mind, a part to find or maintenance to discuss? Get in touch with our team.

Talk to the team450 759-0472Mon–Fri · 8 am–5 pm