Saint-Ambroise-de-Kildare, LanaudièreMon–Fri · 8 am–5 pm450 759-0472
Martin Remorques et V.R. Find my trailer
MARTIN REMORQUES / SALES • PARTS • SERVICE

Trailer bearings and hubs

A dry bearing eventually runs hot, then fails, and it often happens on the highway. At our Saint-Ambroise-de-Kildare workshop, our mechanics inspect, grease and replace your trailer bearings and hubs.

The workshop’s repair and maintenance door, at 270, route 343
WHAT’S INCLUDED

Open, inspect, regrease

Bearing service is the most important maintenance job on a trailer. It’s done hub by hub.

Cross-section drawing of a trailer hub: the spindle, the seal, both bearings and their races, the grease, the dust cap, the hub, the drum and the wheel studs
Trailer hub, cross-section
  1. Removing the wheel, drum or hub

  2. Cleaning out the old grease to see the real condition of the bearings

  3. Inspecting the bearings, races and spindle

  4. Regreasing and replacing the seals

  5. Setting hub play on reassembly

  6. Replacing worn bearings or hubs

  7. A look at the brakes, since the drum is open

  8. Parts ordered through our parts department

THE SIGNS

Listen, and feel the hub

After a trip, bring your hand close to each hub without gripping it. One much hotter than the others is a warning sign.

Recognize one of these signs?

Call the shop or ask for an appointment. We’ll look at the trailer and tell you what it needs.

  • By touch

    One hub much hotter than the others

  • By ear

    A growl or clunk that follows road speed

  • By eye

    Grease on the wheel or tire

  • By touch

    Play when you rock the wheel with the trailer lifted

  • By eye

    Odd wear along the edge of a tire

  • In the service records

    No bearing service in over a year, or a trailer that has been in water

HOW IT WORKS

One hub at a time

  1. You book a time

    Tell us the number of axles and, if you know it, their rating. It helps us plan the parts.

  2. We open the hubs

    Wheel, drum or hub: we take it apart, clean it and look.

  3. We tell you what we find

    A bearing good for a regrease, or one to replace. You see it clearly before we go on.

  4. We reassemble and set it

    Grease, seals, hub play, lug nut torque: everything goes back in place.

How often should bearings be greased?

The simplest rule: once a year, or about every 20,000 km if you travel a lot. Your axle manual gives the manufacturer’s exact interval. A trailer that rarely moves isn’t safe either: grease ages, and moisture finds its way into a hub that sits still for months.

The Martin Remorques store and workshop, at 270, route 343
The store and workshop, at 270, route 343.

Why a bearing fails

A bearing nearly always fails for a simple reason: too little grease, grease that’s too old, water in the hub, or poorly set play. The trouble is it doesn’t warn you for long. By the time you’re on the shoulder, a broken bearing can damage the hub and spindle, and then the repair grows.

That’s especially true on a snowmobile or boat trailer that goes from warm to cold water or snow. The heat drops at once, the hub draws in moisture, and the grease breaks down faster.

And on a used trailer?

If you just bought a used trailer without knowing when its bearings were done, assume they’re due. It’s the first service to plan, and our checklist tells you what else to look at.

Do it yourself or come to the shop?

A handy person can grease their own bearings, as long as they have what they need. You have to lift the trailer safely, remove the wheel and hub, clear out all the old grease, inspect the bearings and races, pack them fully, fit a new seal and set the hub play on reassembly. That last adjustment makes the difference: too tight and the bearing runs hot; too loose and it knocks and wears fast.

Some axles have grease fittings that let you add grease without taking everything apart. They’re handy between services, but they don’t replace a real inspection: fresh grease won’t tell you whether a bearing is marked, and too much grease can get past the seal and onto the brakes. In our shop, the hubs are opened one by one, which also lets us see the condition of the brakes. If you’d rather do the job yourself, our parts counter has what you need. Bring the old bearing or its number if you can: bearing and seal sizes vary from one axle to another, and the numbers stamped on the old parts are the surest way to get the right ones the first time.

When in doubt, don’t wait: a bearing inspected in time costs far less than a hub or spindle that has to be replaced.

WORKSHOP APPOINTMENT

Book a workshop appointment

Tell us which trailer and what work: we call you back to set the date and plan the parts.

Rather talk to someone? 450 759-0472
Monday to Friday, 8 a.m. to 5 p.m.

Work needed

We call you back to confirm the date.

FREQUENTLY ASKED QUESTIONS

Your questions,
our answers

Ask a question
How often should my bearings be greased?

Once a year, or about every 20,000 km if you travel a lot. Your axle manual gives the exact interval.

Is a hot hub normal?

A warm hub after a trip, yes. One much hotter than the others, no: it can come from a bearing or a dragging brake. Have it checked before you leave loaded again.

What’s the difference between a regrease and a replacement?

A bearing in good shape gets cleaned and regreased, with a new seal. If it’s marked, blued or pitted, we replace it along with its race.

How much does a bearing service cost?

It depends on the number of hubs and their condition. Call us at 450 759-0472 with your trailer details: we talk it over with you before we start.

Can I add grease without taking the hub apart?

Only if your axle has grease fittings, and without overdoing it. It doesn’t replace a bearing inspection once a year.

Let’s talk it through

Your next project
Let’s talk

A trailer in mind, a part to find or maintenance to discuss? Get in touch with our team.

Talk to the team450 759-0472Mon–Fri · 8 am–5 pm