Choose your part
How it protects
An ordinary pin and its clip come out in a few seconds. A locking pin goes through the receiver and the shank, and closes with a keyed head: the shank, the ball and whatever is attached stay in place while the vehicle is parked.
Pins come with a bent or a straight head, with a cover that keeps dirt out of the cylinder. Bolt makes pins that code to your vehicle key, and Trimax and Curt offer them in the common diameters.
TrimaxT3 5/8 in. locking receiver pinChoosing the right diameter
The diameter follows the receiver: 1/2 in. for a 1 1/4 in. receiver, and 5/8 in. for 2 in. and 2 1/2 in. receivers. 3 in. receivers take a larger pin, which depends on the receiver.
The length matters too: the pin has to go through the receiver and the shank with room for the head. A wider receiver, an adapter or an extension needs a longer pin.
TrimaxT2 1/2 in. locking receiver pinIn practice
A bike rack or a cargo carrier stays on the vehicle during dinner at a restaurant or the night at the cottage: the locking pin keeps it there. A contractor who leaves the ball mount on the truck protects it the same way.
TrimaxTS32 universal receiver lock with sleeveGood to know
A locking pin also protects the hitch hardware itself: without it, an adjustable ball mount or an expensive carrier comes out in a few seconds. Keep the ball mount inside the vehicle when you are not towing, or lock it in place.
If the shank moves and rattles in the receiver, ask us for an anti-rattle hitch tightener: it takes up the play between the shank and the receiver, and some models lock as well. Over time, that play wears both parts and makes the whole rig noisier on rough roads.
Bolt7023585 5/8 in. receiver lock keyed to your vehicleBeyond the ball
The receiver does much more than tow: bike racks, cargo baskets, hitch steps, removable winch mounts. Every accessory left in the receiver deserves a locking pin, and a keyed-alike set saves hunting for the right key in the dark.
Curt23021 5/8 in. chrome hitch lockDiameters
- Récepteur de 1 1/4 po1/2 in. pin (Class I and II)
- Récepteur de 2 po5/8 in. pin (Class III and IV)
- Récepteur de 2 1/2 po5/8 in. pin
- Récepteur de 3 poLarger pin, depending on the receiver
What we can order
- 1/2 and 5/8 in. locking pins
- Bent or straight head pins
- Pins keyed to your vehicle (Bolt)
- Keyed-alike pin and coupler lock sets
- Longer pins for adapters and extensions
Care
Remove the pin and the shank a few times a season to clean the receiver, and lightly grease the pin: salt and rust can end up seizing it to the shank.
Keep the cover closed and lubricate the cylinder before winter.
Curt23535 anti-rattle hitch lock, 2 in.Ordering at Martin Remorques
Martin Remorques orders its parts from its suppliers, depending on the manufacturer, and receives them at its Saint-Ambroise-de-Kildare counter. Bring the part number, a photo of the part or its label, and the make, model and year of your trailer or vehicle: we check fit, price and lead time before we order.
Our shop in Saint-Ambroise-de-Kildare installs what we sell: hitches, brakes, wiring, axles, bearings, winches and accessories. You leave with a trailer ready to roll, and we keep a note of the part for next time.
You can also come to the counter, at 270, route 343, Monday to Friday from 8 am to 5 pm, with the part to replace: it is often the fastest way to find the right one.

Request a part
Describe the part or give its number: we find the right one, confirm price and lead time, and can install it.
Rather talk to someone? 450 759-0472
Monday to Friday, 8 a.m. to 5 p.m.
Which pin diameter for a 2 in. receiver?
5/8 in. A 1 1/4 in. receiver takes a 1/2 in. pin.
Does the locking pin replace the clip?
Yes, the keyed head replaces the clip and closes the pin.
Can it use my vehicle key?
Yes, with a Bolt pin, which codes to your vehicle key.
What is an anti-rattle hitch tightener?
A part that clamps the shank in the receiver to remove play and noise; some models lock.
Does a locking pin fit a removable winch mount?
Yes, if its diameter and length suit the receiver and the mount; we check both before you buy, so the pin goes all the way through.
How do I order a part from Martin Remorques?
Fill in the part request on this page or call us at 450 759-0472 with the part number or a photo. We confirm fit, price and lead time before ordering.
Can Martin Remorques install the part?
Yes. Our shop installs the parts we sell, by appointment, and checks the rest of the trailer when needed: lights, brakes, bearings and hitch.
Your next project
Let’s talk
A trailer in mind, a part to find or maintenance to discuss? Get in touch with our team.














