Saint-Ambroise-de-Kildare, LanaudièreMon–Fri · 8 am–5 pm450 759-0472
Martin Remorques et V.R. Find my trailer
PARTS · TIE-DOWNS AND STRAPS

D-rings and anchor points

A strap or a chain is only as good as what it is attached to. D-rings, rope rings and recessed anchors give the trailer solid points, in the right places, to tie down all kinds of loads.

D-rings and anchor points

The models

A weld-on D-ring attaches to the frame or the rail and carries heavy loads. A bolt-on ring, on a plate, goes into a solid floor or wall. A recessed ring sits flush in the floor, handy for driving a machine over it. A swivel ring follows the strap’s angle.

Buyers Products makes D-rings, rope rings and weld-on and bolt-on anchors in several ratings, and Faucher transport hardware for trucks and flatbeds.

7830184 4-hole tie-down ring, wide flange, 1,666 lbFaucher7830184 4-hole tie-down ring, wide flange, 1,666 lb

In the right place

Anchors are placed so straps pull outward and forward or backward, at about 45 degrees: four points around the machine hold it in every direction. On a deckover, stake pockets and the rub rail also serve as anchor points.

The anchor has to be at least as strong as the strap or chain: a 1,000 lb ring under a 6,600 lb chain becomes the weak point. It is fastened into the frame or into a floor able to take the pull.

7832008 heavy-duty 4-hole tie-down ring, 2,000 lbFaucher7832008 heavy-duty 4-hole tie-down ring, 2,000 lb

Installation at our shop

Our shop welds rings to the frame of steel trailers, bolts plate anchors through the floor with backing plates, and installs recessed rings. It then touches up the paint or galvanizing to prevent rust.

7835087 anti-rattle 4-hole tie-down ring, 2,000 lbFaucher7835087 anti-rattle 4-hole tie-down ring, 2,000 lb

In practice

A utility trailer owner has four D-rings welded at the corners of the box to tie down the ATV. A hauler adds recessed rings to the floor of an enclosed trailer to tie down machines without getting in the way of pallets.

7830057 3-hole tie-down ring, 400 lbFaucher7830057 3-hole tie-down ring, 400 lb

Good to know

A ring welded to the frame carries far more than one screwed into the wood floor. On a galvanized trailer, welding burns the galvanizing around the ring: our shop then protects it with a zinc-rich primer so rust does not set in.

Recessed rings work well in enclosed trailers and on decks where a machine drives across the floor: they stay flat when not in use and get in the way of neither wheels nor pallets.

7831075 tie-down ring with cup, 500 lbFaucher7831075 tie-down ring with cup, 500 lb

What we can order

  • Weld-on D-rings
  • Bolt-on D-rings and rope rings
  • Recessed rings
  • Swivel rings
  • Backing plates and hardware
  • Installation and welding at our shop

Care

Check the anchor welds and bolts every season, especially after a heavy load. A bent ring or a cracked weld gets replaced.

Touch up the paint around the rings so rust does not set in.

78632 ratchet strap, 2 in. x 22 ft, 10,000 lb, wear sleeveErickson78632 ratchet strap, 2 in. x 22 ft, 10,000 lb, wear sleeve

Ordering at Martin Remorques

Tell us your trailer and what you tie down on it: we choose the anchors, their location and their rating, and install them.

Martin Remorques orders its parts from its suppliers, depending on the manufacturer, and receives them at its Saint-Ambroise-de-Kildare counter. Bring the part number, a photo of the part or its label, and the make, model and year of your trailer or vehicle: we check fit, price and lead time before we order.

Our shop in Saint-Ambroise-de-Kildare installs what we sell: hitches, brakes, wiring, axles, bearings, winches and accessories. You leave with a trailer ready to roll, and we keep a note of the part for next time.

You can also come to the counter, at 270, route 343, Monday to Friday from 8 am to 5 pm, with the part to replace: it is often the fastest way to find the right one.

Martin Remorques in Saint-Ambroise-de-Kildare
THE MANUFACTURERS

Manufacturers of this part type

Faucher

Faucher

Supplier of transportation hardware and tie-down straps for trucks and flatbeds.

7830184 4-hole tie-down ring, wide flange, 1,666 lb7832008 heavy-duty 4-hole tie-down ring, 2,000 lb7835087 anti-rattle 4-hole tie-down ring, 2,000 lb

The availability of a part and of each model is confirmed with the team before ordering.

PART REQUEST

Request a part

Describe the part or give its number: we find the right one, confirm price and lead time, and can install it.

Rather talk to someone? 450 759-0472
Monday to Friday, 8 a.m. to 5 p.m.

The part is for
Installation

We confirm fit, price and lead time before ordering.

FREQUENTLY ASKED QUESTIONS

Your questions,
our answers

Ask my question
How many anchors to tie down an ATV?

Four, one near each corner of the machine.

Can a ring be screwed into a wood floor?

Better to bolt it through the floor with a backing plate, or fix it to the frame.

Should the ring match the strap?

Yes, its rating has to be at least the strap’s or chain’s.

What does installing anchors cost?

It depends on the number and type of anchors and on the trailer; ask for a quote with your trailer details and we give you the price before any work starts.

Can anchors be added to a utility trailer?

Yes, usually welded at the corners of the box or bolted through the floor, so an ATV or a mower can be strapped down properly instead of hooking straps to the sides.

Do D-rings fold down?

Yes, most fold flat when not in use, so they do not catch boots, straps or cargo sliding along the deck.

How do I order a part from Martin Remorques?

Fill in the part request on this page or call us at 450 759-0472 with the part number or a photo. We confirm fit, price and lead time before ordering.

Can Martin Remorques install the part?

Yes. Our shop installs the parts we sell, by appointment, and checks the rest of the trailer when needed: lights, brakes, bearings and hitch.

Let’s talk it through

Your next project
Let’s talk

A trailer in mind, a part to find or maintenance to discuss? Get in touch with our team.

Talk to the team450 759-0472Mon–Fri · 8 am–5 pm