Trailer couplers
The trailer coupler drops onto the ball and locks onto it. It carries the whole tongue weight and holds the whole trailer behind the vehicle: a worn coupler, or one of the wrong size, is not worth keeping.

Choose your part
A-frame or straight tongue
An A-frame coupler sits on the two tongue arms that meet at the front; a straight tongue coupler slides onto the end of a 2, 3 or 4 in. square tongue. Both bolt or weld on. The tongue width and the angle of the arms decide the model.
The latch closes with a lever, a trigger or a flip handle, and locks with a pin or a padlock. A height-adjustable coupler, with several positions, levels the trailer behind different vehicles.
Curt25153 straight-tongue coupler, 2 in. ball, Posi-Lock, 2 in. channel, 3,500 lbSize and rating
The coupler is stamped with the ball size it takes, 1 7/8, 2 or 2 5/16 in., and its rating. It has to cover the loaded trailer’s gross weight. A 2 in. coupler on a heavy trailer is often replaced with a 2 5/16 in., along with the matching ball.
Curt, Demco and Buyers Products make A-frame and straight tongue couplers, bolt-on or weld-on, in every common size.
Curt25210 A-frame coupler, 2 in. ball, Posi-Lock, 5,000 lbHitching properly
The coupler drops fully onto the ball, the latch closes and is pinned, then the tongue is lifted a few inches with the jack: if the ball comes out, the coupler was not properly closed. Crossed safety chains and the breakaway cable complete the hitch.
Curt25474 QuickPin no-latch A-frame coupler, 2 5/16 in., 14,000 lbIn practice
A buyer of a used trailer replaces a coupler whose latch no longer held with a new coupler bolted to the same tongue. A hauler converts the fleet’s trailers from 2 in. to 2 5/16 in. so only one ball is needed across all of them.
Demco05557-95 Demco Slide Lok 2 5/16 in. bolt-on channel coupler, 12,500 lbGood to know
A coupler that does not drop fully onto the ball, because the ball is too big, rusted or dry, can seem closed without being so. The jack check, lifting the tongue a few inches once hitched, shows right away whether the coupler holds. That ten-second step prevents most trailers coming loose on the road.
Demco8705001 Demco DA70 surge actuator for drum brakes, 7,000 lbWorth remembering
Greasing the ball and socket reduces wear and noise, but too much grease collects sand and grit: a thin coat is enough, wiped clean and renewed a few times a season.
Demco8669113 Demco DA91 surge actuator for disc brakes, 8,000 lbWhat we can order
- A-frame couplers
- Straight tongue couplers for 2, 3 and 4 in.
- Bolt-on and weld-on couplers
- Height-adjustable couplers
- 1 7/8, 2 and 2 5/16 in. couplers
- Latches, pins and replacement parts
Care
Grease the socket and the latch mechanism, and check the play on the ball: a coupler that moves a lot is worn. Retighten the coupler bolts at the start of each season.
A cracked coupler or a split tongue around it is fixed right away.
Demco8104002 Demco DA10 weld-on surge actuator for disc brakes, 12,500 lbOrdering at Martin Remorques
Bring the tongue width and shape and the ball size, or bring the trailer in: we find the coupler and install it.
Martin Remorques orders its parts from its suppliers, depending on the manufacturer, and receives them at its Saint-Ambroise-de-Kildare counter. Bring the part number, a photo of the part or its label, and the make, model and year of your trailer or vehicle: we check fit, price and lead time before we order.
Our shop in Saint-Ambroise-de-Kildare installs what we sell: hitches, brakes, wiring, axles, bearings, winches and accessories. You leave with a trailer ready to roll, and we keep a note of the part for next time.
You can also come to the counter, at 270, route 343, Monday to Friday from 8 am to 5 pm, with the part to replace: it is often the fastest way to find the right one.

Manufacturers of this part type
Buyers ProductsBuyers Products
Work truck equipment: toolboxes, warning lights, hitches and snowplow parts.
The availability of a part and of each model is confirmed with the team before ordering.
Request a part
Describe the part or give its number: we find the right one, confirm price and lead time, and can install it.
Rather talk to someone? 450 759-0472
Monday to Friday, 8 a.m. to 5 p.m.
Can a 2 in. coupler be swapped for a 2 5/16 in.?
Yes, if the tongue suits; the ball has to change too.
How can I tell my coupler is worn?
It has play on the ball, its latch closes poorly or its socket is distorted.
Bolted or welded?
Both hold well; we follow the way the tongue was built.
Can the coupler be locked while towing?
Yes, a latch lock or a locking pin closes the lever, which keeps it shut and stops anyone from unhitching the trailer during a stop.
How do I order a part from Martin Remorques?
Fill in the part request on this page or call us at 450 759-0472 with the part number or a photo. We confirm fit, price and lead time before ordering.
Can Martin Remorques install the part?
Yes. Our shop installs the parts we sell, by appointment, and checks the rest of the trailer when needed: lights, brakes, bearings and hitch.
Your next project
Let’s talk
A trailer in mind, a part to find or maintenance to discuss? Get in touch with our team.





